Which section do you wish to go to?

Specifications

Processor / Chipset Intel E7520 – chipset Dual Intel® Xeon(TM) 2.0A, 2.8GHz, or higher (1MB or 2MB L2 Cache) processors in the 604-pin package Memory Eight 240 pin DIMM slots 16GB maximum memory capacity (at this time, only Microsoft® Windows® 2003 Enterprise Edition can utilize memory over 4GB) Supports DDR2 400 ECC Registered Slots Two PCI-E (PCI Express) x8 slots One PCI (32 bit/33MHz) 2.2 slots Two PCI-X (64-bit/100MHz) slots One PCI-X (64-bit/133MHz) slot Onboard Connectors/Devices ATI Radeon™7000 graphics controller Intel® 82541GI Dual Port Gigabit Ethernet Controller Adaptec® AIC-7902 Dual Channel Ultra-320 SCSI adapter Supports Adaptec ZCR & Intel RAIDIOS (Zero-Channel RAID) 2x SATA ports Features Wake up on LAN (WOL), USB, PCI, Mouse Power management Phoenix BIOS

Back I/O Connectors Two rear USB 2.0 ports One PS/2 mouse One PS/2 keyboard One LPT/parallel port One COM/serial port (DB9) Two Intel® Gb Ethernet ports One VGA port Dimension SSI EEB 3.0 form factor 12" x 13"

  Top of page

BIOS Questions

How do I get into the BIOS setup?

Press F2 during the POST (Power On Self Test) process.

Do you have a BIOS history file that includes the problem(s) fixed for each revision of the BIOS?

Yes, click here for the file.

How do I update or flash my BIOS?

Updated BIOS are available on our FTP site.

How do I clear the CMOS?

There is a CMOS RAM onboard that has a power supply from external battery to keep the data of system configuration. With the CMOS RAM, the system can automatically boot OS every time it is turned on. If you want to clear the system configuration, use the JBAT1 (Clear CMOS Jumper) to clear data.

I have flashed my BIOS, but now I get no video!

Try clearing your CMOS (see above). Make sure you've flashed the BIOS using the correct BIOS for your system board; flashing the wrong BIOS will render the board inoperable.

Top of page

Hardware Questions

I've turned the system on, but I'm getting no power (i.e., power supply fan does not spin).

Make sure the cable from the case's power switch is connected properly to the board's power on jumper; refer to the motherboard manual. Try reseating the power connector to the motherboard. Disconnect all the power connectors to your HDD, FDD, CD-ROM, etc. then try powering the system up. Try replacing the power supply.

What kind of DDR DIMMs can I use?

The mainboard provides 8 slots for 240-pin DDR2 DIMM (Double In-Line Memory Module) modules. You can install PC23200/DDR2 400 SDRAM modules on the DIMM slots.

Can I use just one DIMM?

No. Two DIMMs must be populated in a bank.

Can I use different DIMMs?

No. DIMMs must be identical within the same bank. They must also be popluated beginning with the lowest bank..

What is the system's maximum memory capacity?

16GB.

Top of page

BIOS History

Version 1.07 - official release 08/2005

Top of page

System Board Diagram and Picture

System Board Diagram

Click on diagram for an enlarged view (will open in a new window).

System Board Picture

Click on picture for an enlarged view (will open in a new window).

Top of page

Processor Settings
There are no jumpers or DIP switches to configure for the CPU speed. Just install the CPU and the BIOS will autodetect the proper speed and voltage settings.

Top of page

Front Chassis Panel Connector Block (JSSI1)

Top of page

Back I/O Connectors

Don't mix up the PS/2 mouse and keyboard connector, otherwise your keyboard may not work properly.

Top of page

Drivers / Software / User's Manual

 

	System Board Manual (requires Adobe Acrobat reader) - 2MB
	Adobe Acrobat Reader for 9x/Me/NT/W2K/XP

Top of page